Don't take too lightly the forklift at the workplace. If the procedure is not good, there will be major crashes in mins, and there are many mishaps including forklifts.

Case 1: The forklift cargo obstructed the driver's view, and the individual ahead might not be discovered, leading to a moving accident.
Situation 2: In order to keep the balance of the forklift when raising hefty goods, the staff members utilized their body weight as the weight, which practically triggered casualties.
Case 3: The size of the forklift freight exceeds the permitted width of the route and hangs on the roadside shelf, which practically triggers an accident.
Instance 4: Forklift is speeding up and rolls over throughout a turn.
Case 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not see the forklift.
Case 6: The forklift raises the workers illegally, the forklift motorist does not put on the seat belt, the forklift lifter drops and the motorist is squashed when the forklift surrender.
Situation 7: The forklift vehicle driver did not put on a safety belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure must take notice of these issues ：.

Begin.
1. Prior to starting, observe the surroundings, and after confirming that there are no obstacles that prevent the safety of driving, honk the horn first and after that begin.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift starts with a load, the chauffeur ought to first validate that the tons is steady and trusted.
4. The start should be sluggish and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the mast should be slanted in reverse. .
2. Do not lift the fork expensive when driving. When going into and leaving the job website or while driving, beware that there will certainly be no challenges overhead. When the load is taking a trip, the fork must not be raised expensive, which will certainly influence the security of the forklift. .
3. After dumping, the fork should be reduced to the typical driving setting prior to driving. .
4. When transforming, if there are pedestrians or cars close by, the driving signal should be provided initially. High-speed doglegs are forbidden. High-speed doglegs will certainly create the car to shed lateral stability and topple. .
5. When the forklift is downhill, it is strictly restricted to shut off the flame and slide, and it is prohibited to brake unexpectedly while driving with loads unless there are special situations.
6. When the forklift is running, it must comply with the website traffic rules in the factory and must keep a certain safety and security distance from the vehicle in front. .
7. When the forklift is running, the lots needs to be in the lowest setting that does not hinder the driving, and the gantry needs to be effectively tilted back. The tons shall not be elevated except when piling or loading. .
8. The elevation of the load need to not obstruct the driver's sight. In unique scenarios, when the thing impacts the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to activate the ramp, nor to drive across the ramp. .
10. The safe driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a reduced rate when getting in the production Electric Forklift Truck for Warehouse workshop area. .
11. When the forklift is lifted, lifted or driven, it is prohibited for workers to depend on the fork to hold things and play a stabilizing function. .
12. If problems are found, they will be repaired and reported in a timely manner, and they will never ever operate with illnesses or hide them.

packing and discharging.
1. When fork-loading products, the distance in between the two forks must be changed as needed to make the lots of the two forks balanced and not manipulated, and one side of the item should protest the rack. .
2. It is forbidden to deal with a single fork or make use of a fork top or draw. In special circumstances, security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the automobile should be slow-moving and stable. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled objects and injure people. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the load, and it needs to be noted that the fork tip ought to not touch various other items or objects. The tons ought to be supported with minimal back tilt of the gantry to make sure that the load does not glide backwards. The mast can be slanted forward slightly when the tons is decreased to allow for very easy positioning of the load and extraction of the forks. .
6. It is forbidden to fork goods at high speed and hit tough things with the fork head. .
7. When the forklift is functioning, it is prohibited for people to loaf the fork, so regarding avoid the collapse of the goods and harm individuals. .
8. Overloading is prohibited, and it is forbidden to make use of forks to lift personnel to engage in high-altitude operations to prevent high-altitude dropping accidents. .
9. It is not enabled to make use of the brake inertia to slide, put, round or roll things. .
10. It is not permitted to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to discharge the goods or reduced the fork framework.
2. Pull the emergency brake deal with to dead or dispirit the parking brake button.
3. The engine is turned off and the power is removed. (Except for special situations, such as the chauffeur does not leave the automobile's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water should be included.
2. Inspect the security performance of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the procedure of the forklift, examine whether the pressure and temperature level are typical.
5. After the forklift is running, the external leak ought to additionally be checked and the seals need to be replaced in time.

Forklift Safety Operation Specifications.
1. You should examine prior to leaving the automobile;.
2. When you encounter a person before you during driving, you must send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not surpass 5 km/h;.
4. When driving, the nadir of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be also sharp to stop the propensity of "free turning";.
6. Running up and down the slope ought to be slow and consistent, and no activating the slope is allowed.
7. Do not drive throughout the slope. When the gradient is greater than 10%, the vehicle should be driven in reverse when going downhill;.
8. When the forklift employees bring the goods and move on, if they experience huge or hefty items and most likely to the chauffeur's line of vision, they ought to take the turning around workout
.
The "Eight Prohibitions" must be complied with in the operation.
1. Solitary fork procedure is not enabled.
2. Stand-on Electric Pallet Stacker It is not permitted to lift the goods for far away driving.
3. It is not enabled to get the goods by handing over the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not permitted to make use of inertia pressure to grab the goods.
6. It is not enabled to use braking pressure to expatriation round or easy-to-roll items.
7. It is not allowed to bring people to work with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive side to side on inclines
.
Parking is not permitted under the list below conditions.
1. Contours, narrow roadways, train crossings;.
2. Sections with a longitudinal slope greater than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the section with the exact same size as the obstacle must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844